AN-SLZ-80W All-in-One Solar Street Light

The AN-SLZ-80W is one model in the AN-SLZ all-in-one LiFePO4 solar street light series from Shenzhen Anern Optoelectronics Co., Ltd.. It is an integrated unit: the solar panel, the LiFePO4 battery, the LED light source and the controller are built into a single housing, so there is no separate battery box and no separate lamp head to wire on site. For a buyer, the practical consequence is a shorter installation: the unit is mounted on a pole and the system starts working from solar charging, without trenching for cables or a mains connection.

This model is rated at 80W. Its LED light source is 240pcs, 210lm/W, 3000-6500K optional, using Bridgelux LED chips as described for the series. The battery is 768WH LiFePO4, and the solar panel is 18V 100W monocrystalline. The overall size is 1548*385*139mm, and the recommended installation height is 6-9m. Those six figures are this model's own specification row, taken from the published specification table for the AN-SLZ series; no figure on this page is borrowed from another model in the range.

In use, the 80W model suits urban branch roads, industrial park roads and large public squares. The mounting height band of 6-9m is the right way to judge whether this model fits a project: a pole that is too low concentrates the light in a small pool and wastes the wide 140 degree angle, while a pole that is too high spreads the same light over a larger area than the design intends. Buyers comparing models should therefore start from the pole height they already have or plan to install, and then check the panel and battery figures against the lighting hours they need.

The battery and panel figures work as a pair. The 18V 100W monocrystalline panel charges the 768WH LiFePO4 battery during the day, and the battery then powers the light at night. A larger panel shortens the time needed to reach a full charge on a clear day, and a larger battery extends the reserve available for cloudy days. The series is described as providing four to five nights of lighting on a full charge, which is a series-level figure that applies to the range as a whole rather than a promise for any single night in any single location.

Control is by three modes that can be switched with a remote control: light control, which switches the lamp on at dusk and off at dawn; microwave sensing, which raises the output when movement is detected and drops it back afterwards; and remote control operation for manual settings. The PIR sensor distance is more than 8 metres. For a road or a yard, the sensing mode matters because it saves stored energy on quiet hours while still giving full light when a person or vehicle approaches.

The figures in this section describe the AN-SLZ series as a whole, as published for the series: an ingress protection rating of IP66, a working temperature range of minus 25 degrees Celsius to 65 degrees Celsius, an aluminium alloy and PMMA housing, four to five nights of lighting on a full charge, a wide illumination angle of 140 degrees, a PIR sensor distance of more than 8 metres, a solar conversion efficiency of more than 22 percent, and a wind resistance rating of level 16. Three lighting modes can be switched by remote control: light control, microwave sensing and remote control operation. These series-level figures are shared across the AN-SLZ range and are not model-specific claims.

Durability is part of the specification, not an afterthought. The housing is aluminium alloy with PMMA, the ingress protection rating is IP66, and the working temperature range runs from minus 25 degrees Celsius to 65 degrees Celsius. The mounting bracket is die-cast aluminium with a wind resistance rating of level 16. Those figures describe what the unit is built to survive outdoors, but they do not replace a site check: coastal salt air, extreme dust and vandalism risk all still need to be considered when a project specification is written.

No price, minimum order quantity or delivery time is published for this model, and none is stated here. Certificates are available upon request. A buyer who needs the AN-SLZ-80W for a project should name the model exactly in the inquiry, together with the pole height, the road or area width, and the number of nights of autonomy required, so the answer can confirm whether this model or a neighbouring wattage in the same series is the better fit.

Specification of AN-SLZ-80W

A note on model identity: the AN-SLZ-80W on this page is the model in the published AN-SLZ specification table. A separate promotional description of an AN-SLZ2-100W unit, with different figures, belongs to a different series and is not used on this page. Buyers should check the model name on the quotation and on the delivered unit, because the two series names differ by a single character and their figures are not interchangeable.